Editing WIP (section)

==Painting==
The following assumes you will be using acrylic [[Paint| paints]]. Your main two options are acrylic and enamel, the benefits of enamel being crisp colors in one coat, no priming, doesn't chip easy, and no visible brushstrokes. But the downside is it forms a hard coat that is hard to strip, has fumes that will make you sick if not properly ventilated, can really damage your brushes quickly if not cared for, requires chemicals to thin, and has a 24 hour-ish drying time. Enamels are stereotypically Testors brand paints in square bottom glass bottles that are used to paint scale model kits of WW2 tanks and 1960s era cars. These are almost never used with miniatures for games not only for the aforementioned problems, but also because the market for colors and brand variety of acrylics is HUGE. They also can be cheaper. However, enamels are exceptionally good as a basecoat colour for their aforementioned benefits (hard finish, clean surface, can be applied VERY thinly without primer), especially on metal miniatures. A flat black enamel basecoat/primer applied with an airbrush will be superior in every way to even high-end acrylics applied from a spray can. Airbrushed acrylics are a happy middle ground, but still require several coats to form a solid enough layer that is resistant to rubbing.

In general, modelers and hobbyists have moved away from enamels and into acrylics. Enamel can be painted on acrylic, or acrylic onto a primer that was put on enamel if you want to mix mediums (the bright pop of some enamel colors can give a sort of "glow" to things like lights or buttons in vehicle cockpits for example). If applying acrylic paints over enamel without an interim primer, make sure the enamel has properly cured (this can take anywhere up to 48 hours). Do not mix the kind of acrylic paint used for canvas with model acrylics. It doesn't really work because of the differences in pigment size. If you're good at mixing colors and have [[Imperial Guard|balls of steel]] you can look up how to make your own model-grade acrylics from art acrylics and thinner and save yourself a fuckton of money, but it's less consistent and may be wasteful if you don't have a large number of minis to paint.

[[THIN YOUR PAINTS]]. 
No, seriously. It is not a meme. Neither is the wisdom of [[Duncan Rhodes|St. Duncan.]]

See, paints will slowly begin to dry out and get thicker. This results in a chunky, extremely amateurish look that is akin to a crayon drawing of stick figures in the world of miniature painting. 
There's no set rule to how much to thin. Paint will dry at different speeds, and is obviously not all going to be made the same day. Generally, you do not want to thin in the paint pot itself unless you are trying to extend the life of your paint. Use your palette and put some paint in a well. Add a few drops of water and mix it, then brush the side of the well to observe consistency, which you want the same as milk. 

Games Workshop has been known to arbitrarily change the names of their paints, and once even replaced their '''entire''' range with a chemically completely new set. If you use up a pot of paint and have difficulty finding a new one, google it to see if they have changed it recently. 

Check the [[WIP#Paint_Companies| paint companies section]] to choose a manufacturer. 

====Painting Tools====
Important thing to remember, is the tools you use to paint, we don't finger-paint like the cavemen of yore, but with sophisticated sticks with hair glued to the end. More expensive tools are generally better, even in GW's case.

* Brushes: There are lots of different brush types, and are made of a multitude of materials. The cheapest and most common brushes are synthetic brushes, as in the hair isn't made of the fur of some animal, most of them are crap, but more than enough for basing, shading, and layering, they won't last long, but they're really easy to replace. The classical standard brushes are sable brushes, made of a variety of animal furs, like horse or ferret, which differ in stiffness and durability. The brushes are covered in a bit of oil which helps them keep their point. The most expensive sable is the Kolinsky Sable, coming from a species of weasel found in Siberia and Northern China, they're more durable and keep their point longer, and are usually carefully hand-made. There are some expensive synthetics that emulate expensive sables, but those are really for those who believe that the use of kolinsky sable is unethical. Most brushes are round and long that ends to a point, they're versatile and are the best for detail work. There are also flat-head brushes (like GW's base brushes), that are good for painting large basecoats and stuff, and dry/makeup brushes, that are made for... drybrushing and generally are shorter and wider. Some stand out brands are: 
** Winsor-Newton, Da Vinci, and Raphael: these companies make expensive Kolinsky brushes, usually with long bristles, which allows for a larger paint capacity, seriously, if you paint a lot of display standard minis, consider getting one. Don't really bother getting their synthetic ones, because they have worse value than even GW.
** Artis-Opus: Makes some really great soft drybrushes, though consider getting a makeup brush if on a budget, because that's kinda what the Artis Opus drybrushes are. Has good normal brushes too.
** Citadel, Army Painter, Vallejo: The standard "miniature" brushes, Citadels are decent but overpriced, Army Painter and Vallejo, they're fine. They all make similar brushes, mainly differing in the handle they use. Get some of these to start with, but it may be better value to get those packs of 20 crappy synthetic brushes for $10 you find in art stores or on Amazon.
*** No matter what you buy take care of your brushes with a good brush cleaner/conditioner to make them last years (especially Kolinsky and other natural brushes). Cleaner/conditioner is up to taste, but Master's Brush Cleaner & Preserver is simple to use and good with all paints (not just acrylic).

* Painting Handles: You can hold your mini by the base like a barbarian, but any sophisticate knows it's far better to put it on a handle, its more comfortable for youor hand and keeps your dirty body oils off the mini. You can buy ready made types from GW and other companies, but its pretty easy to just take a wine cork and stick some blue tack or a paper clip on it. Great for sub-assemblies too.
** Buy some throw-away plastic shot-glass cups from the dollar store and poster tac from anywhere and stick your mini on top of the base, bada bing bada boom you can now spray primer and hand paint easily.
* Wet Palette: Have you ever made the mistake of buying one of GW's painting palettes? have you noticed that the paint you use dries out in less than a minute and you need to waste more paint on the palette? Well, then you should get yourself a wet palette, they are basically a box with a sponge that absorbs water you pour, and with some parchment paper on top to put paint on. The paint lasts far longer, and can even be usable for weeks. It can save you a lot of money over time. Many companies make their own wet palettes, but you can make your own with a Tupperware container and some paper towel for no money at all, there's dozens of tutorial on Youtube on making your own wet palette.

==== Spraying the base color ====

[[file:AP Spray Paint Guide.png|250px|thumb|right|A guide by The Army Painter for how to use a spray to quickly finish a model.]]

As previously mentioned, you will always want to begin with a primer. Consider a spray or ordinary brush painting the majority color of the model as your next step.
* Pros: speed. This allows you to do models you'll be making many of MUCH faster. Spray [[Ultramarines]] a rich blue, spray [[High Elves (Warhammer Fantasy)|High Elves]] blue or white, spray [[Daemonettes]] a shade of purple or lilac. 
* Cons: there is a downside to the spray effect however, and that is fine detail. For example, chainmail often has a second color beneath the silver, usually black, to give it dimension. Gauntlets and other segmented metals can look fantastic if a small amount of black exists between the joints. These effects can be accomplished in other ways, but are worth considering skipping a spray for.

====Wash/Glaze/Ink====
This aspect of the painting process saves time and produces great effects. All three utilize a very old technique of painting used across many cultures in which pigment or paint is mixed with solvent or suspended in a transparent medium, which results in a colored but partially transparent effect. What many don’t know is the actual difference between the three effects and when to use them. 

* A “Wash” is a transparent effect which will sink into details of a model, changing the color of raised parts minimally while darkening any recesses. The solution composition is a small amount of large chunks of pigment suspended in water, alcohol, or a similar thin liquid. It will tint the model to some degree. For example, a light brown Wash applied to the hand of a Caucasian miniature man will give him a very faint tan, but will make the definitions of his knuckles and the folds of his palm visible. The artist can then, if they choose, go back with the original skin tone and highlight the top of raised edges to keep the detail definition but lose the tanned coloration (of course if they want a tan they can choose to leave the washed skin as it is). Protip, thin metallics with glossy washes.
* An “Ink” is the same as a Wash, <s>but a Wash will dry with a more matte (dull) look and be similar to the degree of shine as what lies underneath (repeated layers of Wash will eventually cause a gloss), while an Ink will immediately cause a gloss effect</s> uhh no, inks are just washes but far more intense in colour, they can be glossy, matte, or satin, same with washes. Inks are different in structure from a Wash because they contain more pigment, which is also usually smaller in grain than the pigment found in a Wash. Citadel used to produce exclusively Inks, but now produce Washes, which they call "shades", fun. Some Inks are really intense, and pretty much requires you to thin it before using. Inks are also great to use through an airbrush, because of their colour intensity and thinness, and are especially great for glazing and zenithal priming.
* A Glaze does NOT sink into recesses, and can be matte or gloss. It tints the entire area it is applied to. In chemical composition, a Glaze is full of small chunks of pigment like an Ink, but in a smaller amount in a thin liquid like a Wash. For example, when applying a light brown Glaze to a Caucasian miniature man hand it will change his entire skin tone to a brown. Applying a blue Glaze to a white piece of armor will dye the armor blue the same as if you had painted it blue to begin with. Glazes are great for quickly producing a specific color if applied to a light base coat. It can also produce quick and easy blending effects, as the transparency of it will naturally blend what lies below with its own effect. Glazes can be used to lighten or darken, and a Glaze can really just be emulated by adding water or medium to ordinary paint. Use it over zenithal undercoat for some good speedpainting. 

Very few models don't need a coat one of the three at some point during the painting process, and for those who are just trying to quickly get miniatures into a decent color scheme for the tabletop they may be the last or second to last step in the process. 

 Become familiar with your options for these, as you can greatly speed up your painting by picking a wash tone and color that allows you to apply the basic colors of the model (skin, hair, metal, cloth), apply the wash, then only do a small amount of highlight and detail work (eyes, emblems) to finish.
When speedpainting, a glaze and a wash are superficially the same thing. The technical difference is that a glaze consistently coats the model much more while a wash sinks into the cracks and stays light on raised parts; using the example of a white Space Marine pauldron and a medium green, the glaze will turn the entire thing a decent green and successive applications will darken that green where it is applied while the wash will turn it a very light green and bring out the details in dark green immediately. As a result glazing is usually not used in speedpainting unless it replaces the base coat step for the dominant color in the model, while a wash is likely to always be used. 

A wash will highlight all the thin details of a model, like cracks in bone or veins in skin. Many modelers accomplish skin tone with a white primer or spray then follow it with a dark wash, saving a great deal of time and effort. Ghostly effects can be accomplished with blue on white spray, and flame effects can begin with red or orange on white. A wash can also give a degree of dimension to a model, as an alternative to the aforementioned "leave some black visible" in the Spray? section.

Inks are not used as often unless intentionally producing a “wet” or metallic effect. Space Marine armor and slimy monsters see the most use of inks, but the popularity of matte effects and only selective use of gloss is favored in the current miniature painting culture. A black ink on grey produces an effect that is reflective without the metallic effects of a silver paint, and is favored by some historical miniature hobbyists or those who prefer a more dull look to their fantasy/sci/-fi. 

The Army Painter and Citadel are the most popular manufacturers of washes. Army Painter makes a large can to just dip models in and give a and vigorous quick shake for fast washing of a large number of minis, though it's really messy and doesn't save much time compared to just brush slapping washes on a miniature. Citadel also has "Contrast" paints, but they are in essence just expensive glazes/inks. Reaper MSP, P3, Vallejo, Daler-Rowney, and a huge amount of other manufacturers also all produce a great selection of inks or washes, buy a few from all of them and see which one you like the best. 

A lesser used but still entirely true /tg/ WIP meme is that the difference between a shit paint job and a decent one is the use of black wash (AKA Nuln Oil from Citadel). 

<gallery>
Image:Beastmen Wash.jpg|The basics of what a wash can do. 
Image:How To Wash.jpg|The basic steps. 
Image:Wash Comparison.jpg|Washes vary more by shade and tone than by company. 
</gallery>

====Airbrushing====
While it may initially seem that airbrushing is some super expensive thing for pro painters, it surprisingly is quite cheap compared to most things in wargaming. 

A decent airbrush will set you back $40-100, and the various other supplies (discussed below) that you will need will cost you around another $40 or so. So...basically around the price of a Warhammer kit. In particular the [https://www.amazon.com/Master-Airbrush-MAS-KIT-VC16-B22-Compressor/dp/B00BF0MW9G|Master Airbrush MAS KIT-VC16-B22 Portable Mini Airbrush Air Compressor Kit] is a decent starter set for only $50 (do not use that airbrush holder on the compressor, it WILL just fall over). 

Actual airbrush use depends on style. It can be easily used to prime models if loaded with a primer, and makes a good middle ground between spray can primer (which can get thick and have issues depending on your climate) and brush-on primer (which takes more time to do). 
You can also accomplish fantastic lighting effects, such as a light caused by gunfire or a light source (imagine a Space Marine illuminated by the blast from his gun, or an adventurer illuminated by his torch). Transition effects on larger models like dragons, phoenixes, or giant spiders can be done in a way that is arguably far better than could otherwise be done. On smaller models you can use an airbrush to turn your small paint pot color into a spray color, as discussed above, so you can then get into detail work. You can also use a blade to cut designs out of paper to use as a stencil, providing you some do-it-yourself decal work that can produce anything from flame paint on a vehicle to Ork checkerboard patterns to scales on a dragon. 

Also, if you're fond of doing arts and crafts for the home you can use a modeling airbrush for just about anything small from holiday decorations (in particular Halloween headstones) to fingernails. Just as an added bonus. 

The following is what you need to know for an airbrush:

* They come in '''Gravity Feed''' and '''Bottom Feed''' variants. Bottom feed requires its own specific bottles, which are premixed although by saving a bottle you can make your own mixes; this isn't really for tabletop miniatures, and is more something for professional or industrial work unless you intend to paint a LOT of things on a ridiculous scale in the same basic colors. You're almost certainly going to want gravity feed, which has a cup at the top where you can pour your paint which is just the same acrylic (it isn't recommended to airbrush with enamel unless you're willing to go through the extended effort in cleanup to ensure it doesn't get gummed up) paint that you use for everything else. Gravity feed works exactly how it sounds, the paint in the cup feeds into the airbrush and is blown out as you press the button. Luckily for you, gravity feed is cheaper! 
[[File:Airbrush Types.jpg|thumb|center|300px]]
* Airbrush sizes for tabletop miniatures range from 0.3mm for detail work to 0.5mm for...well, much less detailed work. Luckily this is the cheap end of airbrush sizes, anything larger would increase the price by a fair amount. So lucky for you!

* You will need a proper cleaning substance to run through the airbrush between paint sessions. While some people use simple dishsoap, the [https://www.amazon.com/Iwata-Medea-Airbrush-Cleaner-16-Oz/dp/B003TJA0S6|Iwata-Medea Airbrush Cleaner] is cheap at $9 and you don't have to worry about longterm buildup or residue. Its strongly recommended that you buy a pot to spray into, which can double as a holder. The [https://www.amazon.com/Master-Airbrush-Cleaning-Palette-Filters/dp/B01M8NI5GA|Master Airbrush Deluxe Airbrush 3 in 1 Cleaning Pot with Holder] is another cheap option at $14, although the seller also offers a kit with cleaning tools; some people claim the tools are useful, others do not. Do some research to determine if you feel they are useful or not. You will want a station to actually spray your models, and at the highest price range you can buy a laboratory-style hood with a fan for $300...or you can just use a large cardboard box and a lamp. Since acrylic paint is not toxic you don't have to worry about fumes, so long as you aren't literally spraying towards your face. Likewise goggles are not really needed, unless you just feel like you want them. You will want to buy some gloves that offer dexterity, nitrile is recommended although if you have allergies, hate the texture, or want something more eco-friendly there's a world of alternatives. 
[[File:Airbrush Box.jpg|thumb|center|300px|Your workstation only has to be as complex as you need to see what you're doing, have enough room to work with, and not turn yourself and the room into a canvas.]]
* Once you get your airbrush, you need to get yourself into an area where you are unlikely to drop anything or have anything roll off and onto the floor, preferably using a large box of some kind, and learn about how your airbrush is put together. Look up the model on youtube for cleaning tutorials and reviews, study any instructions either included or on the website on how it is assembled. You're going to want to take it apart, '''VERY CAREFULLY''' and very slowly so you remember how everything went together, and put it back together while seeing how everything works. This is important because it will help you figure out how it is cleaned and will give you some working knowledge of how it operates. The most expensive part of most airbrushes is the inside needle, which is the part that not only can you quite easily stab yourself with (they are very sharp) but one drop and it will likely be destroyed; it is also most likely going to be the first piece to wear out and need to be replaced, although with good care their lifespan can last years and some people have managed to make do with their first for most of their modelling life. Much like a Marine knowing how to disassemble and clean their weapon (remember Forrest Gump?) you need familiarity in order to use the device properly. 
[[File:Airbrush Assembly.jpg|thumb|center|300px|"THIS IS MY AIRBRUSH. THERE ARE MANY LIKE IT, BUT THIS ONE IS MINE!"]]
* Remember to mount anything you want to airbrush on a wooden stick where it will later be glued (for example an arm should be attached at the shoulder where the blank spot will not be seen), use some kind of tweezers, or have other alternatives to simply touching the model with your hands at the ready. While you can technically airbrush while holding some larger things, it is extremely difficult to work on things like heads this way. 
[[File:Stick Elves.jpg|thumb|center|300px|Not pictured: painted fingers, because there are none.]]
* Before the first time you want to airbush, make sure you have some practice. Set up your station. Use a plastic dropper to put some paint into your pot if its gravity feed, making sure to water it down with another dropper to THIN YOUR PAINT like you would otherwise. On a piece of paper or the surface of your workbench, practice what is called the "dagger technique" where you begin spraying far away, then bring the airbrush closer as you spray sidways creating a line that begins fat and ends sharp. Then do that in reverse, starting with a sharp line and ending in a fat one. Practice trying to shade an area in gradual intensity, experiment spraying from different angles, and do a few designs like writing your name or playing tic tac toe. Then take your cleaning pot and spray out all the leftover paint, fill with cleaning solution and spray that out, then use a soft cloth to clean out the leftover paint. 
[[File:Dagger Airbrush.jpg|thumb|center|300px|The dagger technique teaches you how to be subtle. This is the difference between airbrushing your model and airbrushing your skateboard.]]
* Watch online guides and tutorial videos. There's a world of airbrushing techniques, but due to the nature of the way that the device works you want to know what you're doing before you try and do it unless you intend to experiment. If you discover something that there isn't a guide for, consider making your own to help out the modelling community.

==== Details, Highlights and dry brushing ====
Highlighting has two basic approaches: traditional painting, and dry brushing.
* The traditional method is the same as any painting, just use a brighter/lighter regular colour and sparingly apply it only to the higher parts of the model that naturally see more light, compared to recesses.

*Edge highlighting is simply the application of lighter paint on edge lines, simulating how light catches on edges, best done angling a brush without too much paint 45 degrees and sliding it over the edge. GW's 'Eavy Metal style uses a lot of edge highlighting, even in places where it would be unrealistic, if it's done well, it gives off a sort of super clean, Tron feel, but if done poorly, it just looks tacky and messy. 

* Dry brushing is a technique where a very short-haired brush with thick hairs is used. The colour for it can be a regular one, but Games Workshop also sell specific "Dry" colours such as Necron Compound, whose consistency is more like a grainy mass than a liquid. To do this, dip the brush into the colour, then take a tissue and rub the brush into it until only a fine amount of paint is left on it. Then position the brush over the model and move it up-down or side-to-side in an arcing motion, so that with each contact a little bit of paint ends up on the model until you are satisfied with the amount. With this technique, only the higher portions of the model will receive paint, while the recesses remain untouched. The overall effect resembles a layer of dust to some degree, so it depends on the model if the technique is really appropriate, but it is simple and very fast. Armies that are more "organic" or have lots of rough edges, such as [[Ork]]s or [[Sylvaneth]], work very well with it. Bases are also pretty much universally highlighted by drybrush, as no one has the time to highlight every little rock or grain of sand.

Detail work is pretty finicky, but there are multiple ways to improve on it:
* basic painting technique: as with any regular painting, press your hands together at the lower palms when you paint, so your hand holding the model and the hand holding the brush can only move in unison, this already prevents shaking and improves the result.
* sculpting: sculpted details are naturally better to paint than flat surface free-hands, so consider modelling them on beforehand.
* decals/stickers: most miniatures for games come with applicable decals, and Games Workshop products are no exception. Rather than doing the detail painting yourself, put the decal you want in water, wait a little until it is ready, then use tweezers to apply it. To improve the effect and reduce the visual issue of it being a glued-on sticker, try varnishing the surface first, then varnish the whole thing again once the decal is in place, and/or apply some paint to the transparent area to match it with the area around it. This generally needs experimenting to get right.
* micro-details: first, get an actual detail brush and make sure all the hairs are pristinely in one spot, maybe consider actually removing a few of the hairs to make it even finer if the results are lacking. Do not bother with paint thinning here, instead use the paint itself sparsely to make up for it. Micro-details are things like eyes, teeth, fingernails/claws and the like. If you paint eyes, generally use a tiny amount of white or buff for the eyes, then either black or dark blue for the iris - paint the eye on your "weak hand side" first, because you are likely to slip up. On the side you are strong, you can then just match, making the miniature look into an actual direction instead of having a [[Derp]] face. For creatures like Orks, just use a dot of bright red or something else fitting. Large creatures with big eyes can be more detailed, of course. Claws are best with a base and a lighter layer blend on it, moving outward to simulate a small amount of shadow at the base. Same for teeth. Again, do it sparsely, and it should look just fine.

====Varnish====
Varnishing can be done in one of three ways. These all have different uses and a variety of ways to apply.
*The first and most common is the spray varnish. This is where the infamously expensive GW <s>Purity Seal</s> Munitorium Varnish comes into play, which is known for being easy to apply, has a nice finish that is somewhere between a matte and a satin, and can be easily painted over. They are, as previously mentioned, easy to apply, but overdoing it can result in a frosted and mottled finish. These come in all finishes, so if you want your Wraithlords to be gloss, that's not a problem.
*The second is to do something very similar, but with a brush. The benefits include a very reduced price (you can easily find a bottle of varnish from you FLGS or a hobby store that is twice the size of GW varnishes for half the price), the ability to manipulate coats more easily, as you can paint over just about any bottled varnish with acrylic paints, and the ability to smooth surfaces more easily to make use of things like decals. The downside is that it takes longer to apply, and if you're not careful, can result in thick layers of varnish.
*The third is applying it with an airbrush, put some drops of varnish into the airbrush, add a few drops of water to thin it down, mix, and spray away. Make sure to spray from some distance, otherwise the same procedure as rattle can varnish. 
*The fourth are some inks and shades. Processes like dipping or ''quickshades'' (as Army Painter calls them) have a varnish as part of the mix, so when using them, this will be your last step. The downside is that if you fuck up, there's almost no way to fix it, and if your model is plastic, resin, or [[failcast]], it's almost impossible to strip.

===Basing===
The final step that is skipped by far too many people : taking care of the base, as in painting or decorating the token itself on where the figure is put on. Basing a miniature is visually putting them into their world, rather than as a piece on a game board.

The classic basing method is to throw down some PVA glue and top it with soil, sand, flock, or static grass. This is a good way to produce a very convincing effect for a wide variety of environments. These days, with GW's texture paints, the use of basing paste spread all over the base with some rocks and grass tufts thrown on is becoming more common, it's quick and simple, but has a longer drying time.

=== Paint Companies ===
Most major companies, sadly, do not choose to name their variety of paints and modeling supplies for what they are. Here's a quick guide and overview of the main ones - [[:Category:Tabletop Game Paint Manufacturers| check the category listing]] for more information.

====Citadel====

The [[Citadel_Miniatures#Paints| Citadel painting system]] can sound very confusing and convoluted outside of the 'Eavy Metal "Base, shade, apply at least 14 edge highlights or until all depth is sufficiently lost" method. While it can seem awful and disorganized, having some knowledge as to what makes certain paints clears it up for general use. Actually, its incredibly simple, especially with the mass of tutorials that Warhammer Community has created, but the naming system is pretty inane. Really expensive for what they're worth, it'll save you money not to mainly use Citadel.

=====Primers=====
Citadel only produces dedicated primers in rattle cans, which can be quite frustrating if you live in an exceptionally hot, cold, or humid environment. Luckily, many of their "Base" paints stick well to cleaned plastic models. Chaos Black is a really good primer, but avoid Corax White - if you must get a light Citadel Primer, get one of the two Contrast-ready Primers: Wraithbone for models that will feature skin tones (Orcs, barbarians, Elves), and Grey Seer for models that represent dudes clad in metal ([[Adeptus Astartes|Space Marines]], [[Necrons]], [[Tau]]) or vehicles.

=====Basecoats=====
The Citadel range is split between "Base," "Layer," and "Edge" paints. Base and Edge paints both contain more pigment, and so dry more opaque, but Edge paints have less medium and are harder to thin with water. Layer paints are the same as base paints, but have less pigments so require more coats to get an opaque finish. All can be used as a base, layer, or highlight, you just have to layer and thin appropriately.

=====Air=====
Pre-thinned base/layer paints that are generally thin enough to shoot through an airbrush without thinning, comes in their godawful pots so transfer them to dropper bottles or try your best not to spill when pouring into the airbrush.

=====Dry=====
Exactly as it says, a really thick, almost solid paint that's supposed to be used for drybrushing. Dip your brush in it, wipe away most of the paint on a tissue, then go drybrushing.

=====Shades=====
Citadel produces great washes, called Shades. There are also glossy versions of the common shades, which are useful for metallics. Nuln Oil is often jokingly called "liquid talent", as a simple wash can provide a lot of depth and make your minis look not bad.

=====Contrast=====
Their new Contrast paints are essentially just very high pigment washes - the paints darken in the recesses and leave a tinted highlight on the high points. Works great with a zenithal highlight, and can be used for various unintended effects.

=====Technical=====
Now including their texture pastes, Citadel's technical paints are used to create various cool effects. ''Highlights'' include Blood for the Blood God, which predictably is just realistic looking blood; Valhallan Snow... which makes snow; and Typhus Corrosion, a brown paint with some bits in them, creates a texture that can then be drybrushed orange to look like rust. The 4 clear paints: Lahmian and Contrast Medium, 'Ardcoat, and Stormshield can all be used as varnish or mixing mediums. Technical is perhaps the one line of paints that is worth dealing with [[Citadel Miniatures|The Beast]] for.

====Vallejo====

Probably the most used paint range: if you count scale modellers (in their "Model" range), [[Vallejo]] has a massive range of paint coming in dropper bottles, with especially good metallics. There are multiple ranges - to name a few: 
* "Model Color", for model kits that will be on display
* "Model Air", same but for airbrush use
* "Game Color", more resistant paints for models that will be touched a lot during gameplay, 
* "Game Air", same but for airbrush use
Cheaper than Citadel (per ml, as their pots are 17ml compared to Citadel's 12ml) and the same or better quality too, with the exception of some stinkers. They also make a variety of technical and basing paints, most of which come in large bottles and are quite cheap.

[[Vallejo| Check the article about them]]. Just so you know: your saturday mornings watching Yogi Bear, Scooby-Doo and the Flintstones were Vallejo-colored. 

=====Primers=====
Vallejo makes a variety of Primers in many colours, there are both brush-on/airbrush and rattle cans options. They're really good and durable, and also good value for money, especially compared to Citadel.

=====Basecoats=====
The standard Vallejo paints are the Game and Model Color ranges. Game Color is generally brighter and have more vibrant colours meant for wargaming, with colours that roughly correspond to Citadel ones. Model Color has a larger range, with a lot of different shades of colour which is great for transitions and layering. Very versatile and good value. 

=====Air=====
Simply the regular paints but thinned down (finer pigment) to fire through an airbrush, the air metallics are pretty good, and their thinned down nature makes it easy to use with a brush too. Use these over Citadel Air, the dropper bottles are simply so much more convenient.

=====Metal Color=====
The ''Gold'' standard of metal paints, actually somewhat expensive, but come in 32mL bottles. Mostly just shades of steel/grey metal, but they are the best acrylic metal paints on the market, thin, easy to use, and airbrush ready.

====Reaper====

Eh, pretty much like Vallejo and Citadel. Has a large range, good cost, and some rather interesting colours. Might be easier to find than Vallejo if you live in the US.

====Army Painter====

Cheap paints, really. Basically a cheaper, more diluted version of Citadel and Vallejo paint dropper bottle format. Their Tone washes are great, pretty much the same as the Citadel Shades, but cheaper with less variety. They also make these Quickshade dip cans, where you dip a basecoated miniature in there, then take it out and shake off the excess where it will be all shaded and stuff; quite messy, but good for speed painting. Their metallics are really weak and their primers vary in quality and consistency.  Basically: buy if you're on a budget, otherwise, look at Vallejo or Reaper. Recently switched to a gel medium that makes mixing and thinning a bitch. 

[[The_Army_Painter| Check the article for more information]].

====Scale 75====

Most famous for being matte, really, these paints all have a matte finish, good for those display painters who want to paint their own highlights and have fine control over how the paint looks. They also make inks in their Inktensity line, and extremely bright and intense paint in the FX Flour line.

====MiG and AK Interactive====

Supposedly the same paints, as MiG was founded by a former AK Interactive employee. They're mostly famous in the scale modelling world, but their colours work fine, and they have a good naming scheme - ie: Dark Rust, Shadow Rust, Medium Rust, etc. Both have a lot of different ranges, like Ammo by MiG, and Meng Color by AK. Standout is AK Interactive's newer "3rd gen" range, which have "new" formulas and are really good, worth trying out. They both make Enamel paints, mostly used for either technical effects like chipping, or for recess shading, which enamel paints are great at. They're about the same price as Vallejo.

==== Turbo Dork ====
Specializes in metallics and color-shifting paints, with lots of out-there neon colors. Their Turboshift line is a standard-ish dichroic paint like Vallejo Shifters, but their Zenishift changes color significantly based on whether it's layered on a black or a white basecoat, making it perfect for special effects if you're already doing zenithal priming. Also sells unusual goodies like silicone palettes (just buy an ice cube tray from the dollar store) and mixing sticks .

====Daler-Rowney and Liquitex====

Actual artist paints, but in this list because they make exceptional inks. Perfect for airbrushing, shading, and glazing. They also make mediums that are very concentrated and come in big bottles, make sure to thin them. 

====Prince August and Italeri====
[[Vallejo#Prince_August_and_Italeri_paint_ranges|Rebranded Vallejo - check '''here''' for more information.]]